Get a discount on data recovery!

Disk Structure is Corrupted and Unreadable – What Can You Do?

Read this article to learn how to fix the error “The disk structure is corrupted and unreadable” and understand why it happens. You’ll see how data can be recovered from the disk if the error can’t be fixed.Is your hard disk, memory card or USB drive inaccessible? Do you encounter errors when addressing the hard disk? Read this article to see how to fix the error “The disk structure is corrupted and unreadable”

Disk Structure is Corrupted and Unreadable – What Can You Do?


Overview of the Problem

You can encounter a problem when Windows doesn’t give you access to a hard disk. The system may freeze when the Explorer addresses the disk or just close the Explorer. Such symptoms suggest that your data storage device is either damaged and needs to be replaced, or that important system data is damaged, such as MFT or partition table.

Often you can face such errors when dealing with removable media such as memory cards and USB drives, though there are chances to have them with an HDD or SSD. Let’s see what you can do to overcome this problem and recover data from an inaccessible device.

If there is a problem related to loss of data, you should find out if your device works or not. If the device is broken completely, no software can help you to fix it and recover data. However, don’t jump to conclusions before you run a complex testing and diagnostics of the disk.

Disconnect the Device and Reconnect it Again

In case with a removable media this procedure is as simple as possible. Disconnect a memory card or USB drive using Safely Remove Hardware function. Examine the USB port or card reader visually. If you can find dust, water or damaged contacts, clean the device or try using another port or card reader. Reconnect the USB drive or memory card.

For an internal hard disk or SSD, the disconnecting procedure is also simple. Disconnect the computer or laptop from the power source, remove a few screws to remove a side panel or lid. Find the hard disk and disconnect its power and data cables. For more convenience, you may want to remove the screws to take the hard disk out of the system unit. Examine the disk and both cables carefully for any signs of mechanical damage. A disk may become inaccessible because a cable is fractured or broken, so try connecting the disk with another cable. Both cables should be attached to the disk firmly.

An important note. All connecting or disconnecting operations with the disk should be done only when the power is off. In case with a laptop, disconnect the battery as well.

Reinstall the Device Driver

Remember that updating the driver or firmware of your device may result in a loss of data, so make a backup copy beforehand. It is not recommended to update them for the disk where your operating system is installed.

To update the driver, remove the device from Device Manager; to do it, right-click on the Start button and start the application.

Right-click on the Start button and start the application Device Manager

Extend the Disk drives section, right-click on the problem disk and click “Uninstall”.

«Device Manager». xtend the Disk drives section, right-click on the problem disk and click “Uninstall”

Wait for the disk to be removed and start searching for devices. To do it, select in the menu: ActionScan for hardware changes.

«Device Manager». Wait for the disk to be removed and start searching for devices.

The system will find a new device and suggest installing drivers for it. Use the disk manufacturer driver if the driver installed by Windows keeps generating errors.

Run CHKDSK (disk checking)

Windows OS offers this tool to check the disk, repair logical errors and fix bad sectors. This tools is known as Error checking or CHKDSK. To start it, right-click on the problem disk and select Properties. Then go to the tab Tools and click on the button Check.

Right-click on the problem disk and select Properties

You should run this check as the user with administrator rights. Depending on the disk size and type the check can take up several hours.

As an alternative to this integrated utility, you can also use Victoria. Watch this video for a detailed guide on using it:

Checking the Disk if Windows can’t Boot

If errors in the work of the system disk prevent Windows 10 from booting, you can start disk checking from the Recovery Environment. After three failed attempts to boot, the computer will start the recovery environment automatically. You can also use a Windows recovery drive to run recovery tools. Watch our video to see all ways to enter the recovery environment:

After it boots, run the command prompt from recovery settings and enter the command:


Wait for the operation to be over and restart the computer.

Disk Checking with Disk Management

If the system boots all right and problems begin hen Explorer opens the folder This PC, you can hide the problem disk from the system. It will unlock the Explorer and you will be able to back up the necessary files.

To do it, right-click on the Start button and select Disk Management. You can do the same by executing the command DiskMgmt.msc in the Run window.

Start / Disk Management

Select the problem partition with the right click and choose “Change Drive Letter and Paths for…” then click “Remove” and confirm your choice. It will hide the disk from the Explorer and let you address your system devices without freezes. Be careful not to remove the letter from the system partition – it won’t work.

Recovering Data from a Damaged (Corrupted) Disk

If none of the methods listed above helps you, it is still possible to recover data with Hetman Partition Recovery. Run the program and specify a physical device as an object for scanning. The utility will analyze the disk and list the files available for recovery.

You can view file contents and choose what files you want to save to a healthy disk. When recovering data from a problem disk, always remember that all information there can be lost at any moment. It is for such cases that the utility has a function of creating a disk image.

After such image is created, you can disconnect the problem disk and go on working with the virtual image, without fearing it may crash.

Hetman Partition Recovery. Image Creation

To create an image, select the problem disk and click on “Save Disk” button in the main tab. Specify the path for the image file and wait for the operation to be over.

Hetman Partition Recovery. To create an image, select the problem disk and click on “Save Disk”

To connect a virtual disk in this program, click on “Mount Disk” and specify the path to the image file. After that, a new disk will appear in the program, and you’ll be able to select it for analysis. Watch this video to learn more about data recovery:

Recommended For You